ASTM F1917-20e1 Standard Consumer Safety Performance Specification for Infant Bedding and Related Accessories
基本信息
标准号：ASTM F1917-20e1
发布单位或类别：美国-美国材料与试验协会（US-ASTM）
发布日期：2020-03-01
实施日期：
废止日期：
CCS分类：
ICS分类：
97.140 家用和商用设备、文娱、体育 – 家具
97.190 家用和商用设备、文娱、体育 – 儿童用器具
适用范围/摘要
1.1
本消费者安全性能规范规定了安全性能要求、测试方法和标签要求，以将引言中确定的婴儿被褥和相关配件对儿童的危害降至最低。
1.2
婴儿被褥及相关配件
包括以下用于托儿所的物品:床笠、毯子、防尘褶边、雨篷盖和窗帘、枕头、床垫盖、尿布堆垛机、织物壁挂、婴儿床保险杠/衬里和被子。
1.3
在《消费者安全性能规范》批准日期之后生产的婴儿被褥或相关配件，除非符合本规范中包含的所有适用要求，否则不得通过标签或其他方式表明符合本规范。
1.4
以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换，仅供参考，不被视为标准值。
1.5
以下预防性警告仅适用于试验方法部分第节
7.
，本规范:
本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。
1.6
本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。
1.1
This consumer safety performance specification establishes safety performance requirements, test methods, and requirements for labeling to minimize the identified hazards to children presented by infant bedding and related accessories as identified in the introduction.
1.2
Infant bedding and related accessories
includes the following items intended for use in a nursery: fitted sheets, blankets, dust ruffles, covers and drapes for canopies, pillows, mattress covers, diaper stackers, fabric wall hangings, crib bumper/liners, and comforters.
1.3
No infant bedding or related accessory produced after the approval date of the consumer safety performance specification shall indicate, either by label or other means, compliance with this specification unless it conforms to all applicable requirements contained herein.
1.4
The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5
The following precautionary caveat pertains only to the test method portion, Section
7
, of this specification:
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
研制信息
起草单位：
起 草 人：
归口单位：
F15.19